You should hand tighten the knobs of the Replacement QM3 # TH04997. Anything beyond that is overkill and might damage the hardware/box. view full answer...
The hardware of the etrailer Motorcycle Carrier w/ Ramp for 2" Hitch # e98873 does not have a torque rating this is because the hardware has nylock bushings in the nuts which prevents them from backing off. So using standard hand tools get the hardware hand tight and you'd be fine. view full answer...
The wiring on a brake magnet, no matter the brand, is small. I used our wire gauge measuring tool to measure the wiring on Electric Trailer Brake Assembly - Self-Adjusting - 12" - Right Hand - 5,200 lbs to 7,000 lbs Item # AKEBRK-7R-SA for you. It is 18 gauge.
The matching left hand side assembly is # AKEBRK-7L-SA. view full answer...
You're definitely going to want to check the Viking Solutions Deer Splitter Tool item # 310-VDS001 if you want to make it to Colorado for your trip. This tool was designed to cut through the chest cavities, pelvic bones, and jaw bones of a kill. It'll even cut through a deer's pelvis that weighs up to 200 lbs. They're not going to let you throw this in your carry on.
The blade length on the Deer Splitter Tool item # 310-VDS001 is 4" and the overall dimensions are 11-1/2" long x 1" thick.... view full answer...
The Lippert Smart Jack Electric Trailer Jack w/ Footplate # LC643589 has the following dimensions above the mounting plate. It is 21.6" tall, 6.165" wide at the widest point of the head and 9.385" deep at the widest points. I have included an image to help you see these measurements.
The manual override nut on the jack is a 19mm hex head bolt.
I recommend the Bottom Support Plate # JSP-100 for helping you to create a mount on the frame of your boat trailer to hold the Smart Jack. view full answer...
For the installation hardware for the Curt Hitch item # C13234 you will want the Replacement Hardware Kit item # RHK. This will include the correct grade bolts, spacers, nuts, and fish wire tool needed to install this hitch on your Ford Edge. You will want to go to the right hand side of the product page and above where it says add to cart you will see a box that is labeled Hitch Item Number. In this box you'll need to put C13234.
I have linked the instructions for the Curt item # C13234... view full answer...
Your Jeep looks great! It looks like this box will fit perfectly. The overall weight of the DeeZee Storage Box # DZ6535P is 17 lb. and it is made from a sturdy poly-plastic.
It's hard to tell from your photo what thickness of plywood you're using. Depending on the thickness of the plywood and the weight of the tools you'll be carrying, you may need to add some additional support. Plywood strengths vary based on thickness. The most popular thickness in home use is a 3/4" fir plywood.... view full answer...
Yes, we do just sell the hardware kit for the Draw-Tite 36280 hitch. You will want the Replacement Hardware Kit for Trailer Hitches item # RHK. This will give you all of the bolts, nuts, spacers, washers, and even the fish wire tool that your hitch requires for install. The bolts will be of the correct grade too so you won't have to worry about a parts failure due to a cheap grade bolt. I have attached a picture below of the hardware you will be receiving.
When you go to the Replacement... view full answer...
Yes, we do sell just the hardware for Curt, Da'Lan, Draw-Tite, etrailer, Hidden Hitch or Reese trailer hitch receivers. You will want the Replacement Hardware Kit for Trailer Hitches item # RHK. This will give you all of the nuts, bolts, spacers, and even a fish wire tool if your hitch requires them for install. The bolts will be of the correct grade too so you won't have to worry about a parts failure.
You will need to know your hitches part number. When you go to the Replacement Hardware... view full answer...
Yes, we do sell replacement hardware kits. You will need the Replacement Hardware Kit item # RHK. This kit will include all the necessary bolts with proper grades, spacers, nuts, and the fish wire tool you will need to complete the installation. The price is on the right side of the product page.
You will want to go where it says Hitch Item Number on the right hand side of the page and type yours in. It looks like there are only two class III hitches for the 2001 Honda CR-V and I have... view full answer...
The hitch I recommend for your 2015 Toyota Prius is the Draw-Tite # 24847. This Class I hitch has a 1-1/4-inch receiver opening and it has enough tongue weight capacity (200-lbs) for a 2-bike rack and your two road bikes. Installation is shown in the linked video; hardware is included and the written instructions are also linked.
Mostly basic hand tools are required to mount the hitch to the car's frame but you'll also need a torque wrench like # ALL944001 to secure the included fasteners... view full answer...
The Draw-Tite Class III trailer hitch, part # 75902 you mentioned has a 3500 lb towing, 350 lb tongue weight (the maximum amount of weight that can safely be suspended from the hitch) capacity. This hitch is NOT compatible with Krom models. However, these capacities will be limited by the actual towing capacity of the Rouge, which is lower. I did some online research, and found that the 2010 Nissan Rogue with the CVT transmission with the manual shift mode is capable of towing up to 1500... view full answer...
Go To Results